Видео

fuking scum just show me

Do you add new freon or use the same freon that was already in it? 2:56

How much does this compressor cost? Mine went out and it costs $900 + $90 for taxes. Was this a reasonable price? It was very interesting watching your mechanical work. Thanks

exact problem lol i went over a bump and it wouldn't start, ordered parts off amazon wish me luck 😂

Thank you for this vid. It will help me later today. Here is your like:)

Super clear video. Thank you

Gutter doesn’t clog because nothing, not even water, gets through the mesh

What the heck is that Bubba Rig at the begining of the video???

My speedometer works sporadically and only for a few seconds I changed the vss sensor but it still doesn't do anything I also changed the cluster Could doing what you show in your video work?

Why did you not have to add pag 46 oil sir?

What if you don't hear it Click, when you push the sensor in ????

Donde puedo comprar ese maquina para meter aire al carro

You sir is definitely a life saver. I had gave up on this car at first, until I came across this video 🙏🏾💪🏾👍🏾

When do you put the starter gear on?!!!

Que pasa si quite la bobina para quitar el motor de arranque?

What did you about the piece of aluminum that broke?

THIS GUY WOULD SCREW UP A ABORTION.

Thanks For Sharing...It's Getting Really Hot and My Babies Gotta have AC....My High Line has a Hole Where the rubber Hose is on The Bottom of My 2002 F150...Where Gonna pull a vacuum 1st Then Have a Go at....from What I see It's Loosening The top and just a 10 mm at The Compressor

Thanks For Sharing...It's Getting Really Hot and My Babies Gotta have AC....My High Line has a Hole Where the rubber Hose is on The Bottom of My 2002 F150...Where Gonna pull a vacuum 1st Then Have a Go at....from What I see It's Loosening The top and just a 10 mm at The Compressor

Great show, sir!

10$ a month

Thank you so much for making this video! I'm having rough idle issues with my 95 accord ex and have changed so many parts and cleaned so much stuff. I'm going to try this next. Thank you again!!! 👏🏾👏🏾👏🏾🫡🫡🫡

Hello this looks to be from about 3 years ago but i have a 2004 f150 5,4 l and when i put it in drive its like netural but sometimes it will catch when the RPM is high and slam into geat but usually i drop it into 2nd and roll a little then back to drive and its good till i slow down and it does it again and it may do it a little in 2nd once in a while, any idea ?

So with mine, the tire keeps moving out of rim. Apparently because there were 2 small cracks in the rim. They fixed this, but same problem again, wheel goes down and when I feel behind the wheel I can feel the space between rim and wheel. What could be the issue?

I love that all the idiots that want to correct you are wrong them selves. Its not an o2 its not a map. Its not a maf. Its an ats kep doing what your doing buddy. Ignore the ignorance

❤❤

No se debe quitar el filtro si no las impurezas pueden taponar el inyector una vez limpiado si se puede cambiar el filtro

Was that a tinted clear coat? It says color match on the can, or just regular clearcoat? Thanks

What was that polishing pad you used?

Are the 4 cylinder and V6 engine use the same starter?????

Question, will my engine leak oil if its the head gasket or no? My bike has been overheating and i noticed my intake manifold was jacked up shortly after that so I'm not sure if the manifold is causing the overheating or the head gasket. I still haven't reinstalled a new intake yet.

What happens to the bracket?

What if it is leaking air, and deflates fast when driving. Can i use a hammer on aluminum rim, for inside bend? The bend looks the same as yours but its inside and has a crack on the bend section

I've worked for them on and off for five years. Gas allowance is definitely listed separately. Always has been. The product is quite expensive, but that is the ONLY thing this guy says that I can agree with. You can make great money as an installer. $100,000/yr working 5 days per week is completely achievable in most areas that the company has an office. Plus, as with most sub contractor positions, you can work as little or as much as you want, with little to no forewarning to the company. Idk man, this guy sounds like a send off

There’s supposed to be a beveled interior snap ring in the groove of the magnet to stop it from being pressed too far on and from coming loose and from running into the back of the pulley and wrecking the magnet or the magnet plug

I applaud this repair and its expectations.

Can someone explain why people would give a video showing rotted tires a thumbs down?

I want to know why you didn't clean that gear and put some transmission fluid on it and then put it on the new speed sensor that's what I call half-ass work

Excelente aprendí algo nuevo como arrancar el motor para vaciar lo poco dé aceite viejo mis felicitaciones 🙏

Don’t go with Leaf Filter, and I’m here to say why. I had them installed only on my back patio gutter, and it was $3,000. That was just a year ago this past March, and the gutter is already clogged. So I called them to have someone sent here to fix that. They said it would cost me $97, because my one year warranty was up. So much for their so called “Lifetime No Clogs Guarantee” 😑

Good video 👍

Gracias por tu video, me ayudó mucho❤

Si mi valvula egr no tiene vacio es porque falla esa pieza ?

el vice grip no es martillo .

Had to take out battery to change my starter once I finished my idle was so bad at zero and would die thanks for the video it worked out saved me 200$$ FYI had to run 10 minutes in drive with e break on thanks for video

What noise was it making? My 2010 corolla ac is making a little noise. Almost whining a little. Still works tho. Wondering if i should just keep sending it until something breaks. 240k miles on it hate throwong $ at it.

This video really make sense on fixing the oil leaks. Good job!

Dang you guys are some top level techs in this comment section. 👀

Did you need to reprogram the ecu?

That's what happens when you don't use the proper tools for the job in the first place. There are proper bleeder wrenches that prevent bleeder mangling. Also note, make sure the tiny rubber caps stay on the bleeder screws to prevent rust and dirt from entering the inside of the bleeder, making this job ten times worse. Then you need to use heat. Lots of it!!😅